- Car Diagnostic Tool
- Launch Series Tool
- Auto Key Programmer
- ECU Chip Tuning Tool
- Odometer Correction Tool
- Autel Diagnostic Tool
- Car Electronic Tester
- ELM327 Diagnostic Tool
- Auto Code Reader
- OBD Cable&Connector
- Ediag Tool
- Car Key&Chip
Add：NO. 15 Kuiping Road, Longgang, Shenzhen, China
Launch Creader 3001 CR3001 Full OBDII Scanner OBD2 Engine Co
Launch Creader 3001 CR3001 Full OBDII Scanner OBD2 Engine Code Reader
Launch CR3001 provides full OBDII/EOBD diagnostic functions and meets protocols such as ISO9141-2, ISO14230-4, SAEJ1850, and ISO15765-4.
*Support Full OBD2 functions,checking engine as follows:
1.Reading Codes: show the detailed description of the diagnostic Trouble Code (DTCs).
2.Erasing Codes & Reset: turns off Check Engine Light (MIL), clears codes and resets monitors.
3.Data Stream: reads and displays live ECU/PCM data stream, plot functions graphically and stores freeze frame data.
4.I/M readiness status: Shows whether the various emissions-related systems on the vehicle are operating properly
and are ready for inspection and maintenance testing.
5.Read Live Data Stream: Show the information of continuous data stream from a vehicle in live graphic (waveform) display.
6.View freeze frame data: Check the certain vehicle conditions which are recorded by the on-board computer
when the emission-related fault occurs.
7.O2 sensor test: allows retrieval and viewing of O2 sensor monitor test results for the most recently performed tests
from the vehicle’s on-board computer.
8.On-board monitor test: retrieves and displays test results for emission-related powertrain components and systems.
9.Read Vehicle Information: display the information such as VIN (Vehicle Identification Number),
CID (Calibration ID) and CVN (Calibration verification number),etc.
10.Component Test: certain vehicle components can be actuated by commands sent from the scanner to test their operability.
11.Turn Off ''Check Engine'' Light
Parts might cause your check engine light on include:
* Gas Cap b.Oxygen Sensor
* Air Fuel Ratio Sensor
* Mass Air Flow Sensor
* Ignition Coils
* Spark Plug Wires
* Spark Plugs
* EGR Valve
* Evaporatative Emission Canister Purge Valve(EVAP)
* Catalytic Converter.
If the engine light doesnot turned off in time ,it will cause environmental pollution,
increased fuel consumption,increased engine noise, increased in temperature, ect.
How to verify whether the vehicle will pass the emission test with this code reader?
After entering the I/M Readiness, there will be 10 results on the list. Misfire monitor,
fuel system, componentmonitor, catalyst monitor, heated catalyst, EVAP system,
secondary air sys, 02 sensor, O2 sensor heater EGRand/or WVT.
There will be an OK if each of them works fine. [Not all vehicles have these 10 parts]
Support Language: English , French , Russian , Spanish ,German, Italian ,Portuguese
Support car models
(Note: CR3001 only Support 12V Gasoline& Diesel, Does not support 24V Truck )
CR3001 Support OBD 2 protocols car :
1.SAE J1850 PWM(41.6Kbaud)
2.SAE J1850 VPW(10.4Kbaud)
3.ISO9141-2(5 baud init,10.4Kbaud)
4.ISO14230-4 KWP(5 baud init,10.4 Kbaud)
5.ISO14230-4 KWP(fast init,10.4 Kbaud)
6.ISO15765-4 CAN(11bit ID,500 Kbaud)
7.ISO15765-4 CAN(29bit ID,500 Kbaud)
8.ISO15765-4 CAN(11bit ID,250 Kbaud)
9.ISO15765-4 CAN(29bit ID,250 Kbaud)
American Car :
Need Standard OBD2 Protocols from 2000 to now. Available for Chrysler/Ford/GM/Jeep ...
European Car :
Need Standard OBD2 Protocols from 2003 to now.
Available for Alfa romeo/SAAB/Acura/Opel/Audi/Seat/Peugeot/Renault /Bentley/Skoda/Daewoo
Need Standard OBD2 Protocols from 2006 to now.
Available for KIA/Isuzu/Honda/Mitsubishi/Hyundai/Dacia/Lexus/Mazda/Nissan/Subaru/Suzuki/Toyota...
Need Standard OBD2 Protocols from 2009 to now
Screen :1.77 " TFT, 160*128dpi
Voltage Range: 9-18V
Operating Temperature :0℃ -50 ℃ (32 ℉ -122 ℉ )
Environment Temperature -20 ℃ -70 ℃ (-4 ℉ -158 ℉ )
Dimension : 118mm*68mm*22.3mm(4.65" *2.68 " *0.88 " )
Categories:Launch CR Code Reader Tool